dc/dc converters tes 2m series, 2 watt features ultracompact smd-package i/o isolation 4000 vacrms rated for working voltages up to 300 vrms operating temp. range C25c to +80c qualifed for leadfree refow solder process available in tape & reel package ordercode input voltage range output voltage output current max. effciency typ. tes 2-0511m 5 vdc 400 ma 66 % tes 2-0512m 5.0 vdc 10% 12 vdc 165 ma 66 % tes 2-0513m (nominal 05 vdc) 15 vdc 133 ma 66 % tes 2-0522m 12 vdc 83 ma 72 % tes 2-0523m 15 vdc 66 ma 73 % tes 2-1211m 5 vdc 400 ma 66 % tes 2-1212m 12.0 vdc 10% 12 vdc 165 ma 66 % tes 2-1213m (nominal 12 vdc) 15 vdc 133 ma 66 % tes 2-1222m 12 vdc 83 ma 74 % tes 2-1223m 15 vdc 66 ma 75 % tes 2-2411m 5 vdc 400 ma 66 % tes 2-2412m 24 vdc 10% 12 vdc 165 ma 66 % tes 2-2413m (nominal 24 vdc) 15 vdc 133 ma 66 % tes 2-2422m 12 vdc 83 ma 74 % tes 2-2423m 15 vdc 66 ma 75 % models the tes 2m series is range of compact 2w dc/dc-converters providing a high i/o-isolation voltage of 4000 vac. with a reinforced i/o-isolation system this pro - duct is an economical solution for many applications in instrumentation, industrial controls, medical equipment and everywhere where supplementary- or reinforced insulation is required. these converters are qualifed for high solder temperature profles in leadfree sol - der processes. for automated smd production lines the devices can be supplied in tape & reel package. full smd-design with exclusive use of ceramic capacitors ensure a very high reliability and a long product lifetime. page 1 of 3 c b scheme iec 60950 -1 iec 60601-1 http://www.tracopower.com pending
dc/dc converters tes 2m series 2 watt input specifications input current no load 5 vin models: 60 ma typ. 12 vin models: 30 ma typ. 24 vin models: 15 ma typ. reverse voltage protection 0.3 a max. recommended input fuse (slow blow) 5 vin models: 1.0 a 12 vin models: 0.5 a 24 vin models: 0.2 a surge voltage (1 sec. max.) 5 vin models: 9 v max. 12 vin models: 18 v max. 24 vin models: 30 v max. input filter internal capacitors output specifications voltage set accuracy 4 % voltage balance (dual output models) 1 % max. regulation C input variation 1.2 % / 1 % change of vin C load variation 20 C 100 % 10 % max. 12 % max. for 5 vout models. ripple and noise (20 mhz bandwidth) 150 mvp-p max. temperature coefficient 0.02 %/k short circuit protection 0.5 sec. max. minimum load 2 % of rated max current. capacitive load single output models: 330 f max. dual output models: 100 f max. (each output) general specifications temperature ranges C operating C25c to +80c C storage C55c to +125c C case temperature +90c max. derating 2.5 %/k above 60c humidity (non condensing) 95 % rel. h max. reliability, calculated mtbf (mil-hdbk-217f at +25c, ground benign) >2.0 mio h isolation voltage (50hz, 60sec.) C input/output 4000 vacrms isolation test voltage (1 sec.) 6000 vpk leakage current (at 240vac, 60hz) 2 a max. isolation capacitance C input/output 20 pf max. (at 100khz, 1v) isolation resistance C input/output >10 gohm (at 500vdc) safety standards iec/en 60950-1, iec/en 60601-1 3rd edition, 2 x moop cul/ul 60950-1, ul 60601-1 safety approvals C cb test certificate (iec 60950-1& iec60601 -1) www.tracopower.com/products/tes2m-cb.pdf switching frequency 50 C 100 khz (pfm) environmental compliance C reach www.tracopower.com/products/tes2m-reach.pdf C rohs directive 2011/65/eu all specifcations valid at nominal input voltage, full load and +25c after warm-up time unless otherwise stated. page 2 of 3 http://www.tracopower.com pending
sp ec i?cati ons can be changed wi thout noti ce! make sure you are using the latest documentation, downloadable at www.tracopower. com www .tracopower. com dc/dc converters tes 2m series 2 watt rev. april 10. 2013 page 3 of 3 outline dimensions pin single dual 1 Cvin gd Cvin gd 7 o con. o con. 8 o con. common 9 +vout +vout 10 Cvout Cvout 16 +vin +vin pin-out physical specifications casing material plastic weight 3.8 g 0.13o ead-free reflow solder process as per -std-020d.01 (to find at: www.edec.org - free registration required) moisture sensivit level (msl) level 2 as per -std-033b.01 (to find at: www.edec.org - free registration required) ashing process www.tracopower.com/products/smd- wash.pdf pacaging www.tracopower.com/products/tes2m-pac.pdf dimensions in [mm], () = inch tolerances 0.25 (0.01) pin pitch tolerances 0.05 (0.002) 24.0 (0.94) 0.25 (0.01) 9.0 (0.35) 1.1 (0.71) 13.7 (0.54) 15.24 (0.60) 2.54 (0.10) 3.11 (0.12) top view 17 16 10 9 0 - 4 0.15 1.0 (0.04) 2. (0.11) 13.7 (0.54) 15.24 (0.60) 2.54 (0.10) 3.11 (0.12) 1.4 (0.055) min. 2. (0.11) solder pad dimension application note: www.tracopower.com/products/tes2m-application.pdf
|